NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. Command Default None Command Modes Any command mode Command History Release Modification 4. I was normally using it, when the screen went black and the phone just shut down. Examples This example shows how to display all configured command aliases: switch show cli alias This example shows how to display a specific command alias: switch show cli alias name ethint Related Commands Command Description cli alias name Configures command aliases. Command Default Displays only the configured information.
This command will have most of the information which you can go through with your own tools at your desk or with another engineer. Command Default Displays the entire formatted history. Usage Guidelines The show switchname command also displays the switch hostname. Command Default Displays information about the terminal port configuration. Examples This example shows how to display a specific license installed on the switch: switch show license file fc5020. Step 5 switch config-job copy Optional running-config startup-config Saves the change persistently through reboots and restarts by copying the running configuration to the startup configuration.
The location can be in bootflash or volatile. Expiry Date License expiry date. Important Procedure Command or Action Purpose Step 1 switch configure terminal Enters global configuration mode. Examples This example shows how to display the hostname for the switch: switch show hostname switch switch Related Commands Command Description hostname Configures the hostname for the switch. Time: Tue Jul 13 06:05:42 2010 version 4.
The valid range is from 1 to 3. This platform is optimized for high-density. Sounds like your power button is stuck down. I tried holding it down it still goes into a lopp where it would attempt to start up, fail and retry, no matter what I do, press the button once or hold it down. Command Default Displays license usage for the switch.
Command Default Displays memory allocated to the processes. Try to understand what the general complaint area is. They can be used with the above-mentioned Nexus 2000 series fabric extender. This sample is defined by a range that you can configure. Examples This example shows how to display the hostname for the switch: switch show switchname Related Commands Command Description hostname Configures the hostname for the switch. Please improve this by adding.
If you hold the power button for 15 seconds, your phone should shut off. Simple but sweet, this just shows you how to get the serial number for all the modules in your Catalyst 6500 switch. Previously, the Nexus 6000 series was meant to be focused on the Cisco 40G aggregation products, and the 5500 and 5600 series on 10G. Usage Guidelines The output from the show tech-support command is very long. Table 1 show license usage Columns Column Description Feature Name of the license package. The packet is decapsulated at the destination router and then sent to the destination interface.
The traffic is encapsulated at the source router and is transferred across the network. This will allow you to prove that you own the smartphone in case the Nexus 5X gets stolen and you want to get it back. If you ever sell it, people want it. There are no special NetApp markings in the hardware or software. However, if management is configured, it will not be listed in the output of the show-running command because it is the default.
Some details on the models are detailed below. Recommended Action: Reinstall the correct license for the chassis where the supervisor module is installed. Command Default Displays all hardware inventory information. The filename is case sensitive. The first chassis in the Nexus 7000 family is a 10-slot chassis with two supervisor engine slots and eight module slots at the front, as well as five modules at the rear.
Step 4 switch config copy running-config Optional startup-config Saves the change persistently through reboots and restarts by copying the running configuration to the startup configuration. Verify that the Product Authorization Key that you used to order the licenses comes from the same chassis from which you retrieved the chassis serial number. Startup config saved at: Fri Jul 9 23:19:25 2010 version 4. The 2000 series consists of 4 different models. Licensing Installation Issues Serial Number Issues Make sure that you use the correct chassis serial number when ordering your license. The serial number must be for the same chassis on which you plan to install the license.
Feature Name Releases Feature Information 5. Use the show license host-id command to obtain your chassis serial number. Default Settings for Online Diagnostics The following table lists the default settings for online diagnostics parameters. I was stupid enough to not ask him to copy down the serial number beforehand. I'm not really into customization and that sort of stuff so my phone's software is the same since the day I bought it, I don't even recall doing any software updates or downloading any apps before the phone crashed down the first time.